The length of the tube necessary for the boundary layer to reach the centre of the tube and for fully developed flow to be established is called the __________ length. Fluid Mechanics

  • Equivalent
  • Transition
  • Prandtl mixing
  • None of these
Answer: Transition
576 students attemted this question.

Explanation

No Explanation Available.

Share this question with friends

Similar Questions

  1. Which of the following must be followed by the flow of a fluid (real or ideal)? (I) Newton's law of viscosity.(II) Newton's second law of motion. (III) The continuity equation.(IV) Velocity of boundary layer must be zero relative to boundary.(V) Fluid cannot penetrate a boundary.

  2. Very small pressure difference ( A. U-tube water B. U-tube mercury C. Inclined tube mercury D. Inclined tube water Answer & Solution Discuss in Board Save for Later Answer & Solution Answer: Option D No explanation is given for this question Let's Discuss on Board 20. A fluid which has a linear relationship between the magnitude of applied shear-stress and the resulting rate of deformation is called a/an __________ fluid. A. Newtonion B. Non-Newtonion C. Ideal D. Incompressible Answer & Solution Discuss in Board Save for Later Answer & Solution Answer: Option A No explanation is given for this question Let's Discuss on Board 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Read More Section(Fluid Mechanics) Each Section contains maximum 70 questions. To get more questions visit other sections. Fluid Mechanics - Section 2 Fluid Mechanics - Section 3 Fluid Mechanics - Section 4 Fluid Mechanics - Section 5 Fluid Mechanics - Section 6 Fluid Mechanics - Section 7 Fluid Mechanics - Section 8 Fluid Mechanics - Section 9 Fluid Mechanics - Section 10 Fluid Mechanics - Section 11

  3. Applying a pressure drop across a capillary results in a volumetric flow rate 'Q' under laminar flow conditions. The flow rate for the same pressure drop, in a capillary of the same length but half the radius is

  4. The energy loss in flow through ven-turimeter is less than that through flow nozzle, because in case of a flow nozzle, the

  5. The diagram shows a U-tube with cross-sectional area A and partially filled with oil of density ρ\rhoρ . A solid cylinder, which fits the tube tightly but can slide without friction, is placed in the right arm. The system is in equilibrium. The weight of the cylinder is:

  6. Capillary rise of mercury in a small diameter tube is proportional to (where, d = diameter of the tube, σ = surface tension of mercury)

  7. The __________ pressure is measured by a static tube.

  8. In one dimensional flow, the flow

  9. Bernoulli's equation cannot be used for flow of water in river because the flow is

  10. In which type of fluid flow, the velocity of flow of fluid changes from point to point in the fluid at any instant?

  11. Liquid delivery by centrifugal pump starts, only when the head developed by it is equal to the __________ head.

  12. The Property of the fluid which offers resistance to the movement of one layer of fluid over another adjacent layer of the fluid is known as

  13. According to Archimede's principle, if a body is immersed partially or fully in a fluid then the buoyancy force is _______ the weight of fluid displaced by the body.

  14. A stone tied up to the spring balance then dipped in the water. After reach a certain depth, the weight of stone decrease as shown. What is the buoyant force exert on the stone?

  15. The rate of change of velocity due to change of position of fluid particles in a fluid flow is called as

  16. A force that is caused due to attraction of particles in the layer of fluid bulk is called?

  17. A bath toy weighs 1.2 N outside of the tub, the in tube it had an apparent weight of .75 N, what is the buoyant force acting on the toy?

  18. Calculate the Capillary rise in a glass tube of 2.5 mm diameter when immersed vertically in mercury. Take surface tension, σ =0.52 N/m for mercury in contact with air. The density of mercury is given as 13,600 kg/m3 and angle of contact =130°

  19. Rise of liquid in a capillary tube is due to

  20. With increase in molecular weight of the gas, the head developed by a centrifugal compressor will

Comments

Add Your Review

Your email address will not be published.

Subscribe to Newsletter!

Subscribe to get latest updates and information.